Magnetic Flow Meter JIS10K Flange Type
1. Introduction
MLF electromagnetic flowmeter works according to Faraday's law of
electromagnetic induction, and is composed of sensors and
converters. Used to measure the conductivity of liquid or solid. In
general, its conductivity should be greater than 5μs/cm (tap water
and raw water conductivity is about 100 ~ 500μs/cm), and it can
also be used to measure acid, alkali, brine, pulp or pulp and other
media. However, these media cannot contain a large amount of
magnetic substances and bubbles.
2.Working Principle
The principle of the sensor is based on Faraday’s law of
electromagnetic induction.
It is installed a pair of detection electrodes on the pipe
wall,where the measurement pipe axis and magnetic field lines are
vertical. When the conductive liquid cuts magnetic field lines and
produces induced electromagnetic force.Which can be measured by the
two electrodes on the
meter pipe.The result can be calculated by formula: Induced
electromotive force,(flow signal) E=KBDV
E——Induced electromotive force,V；
K——meter constant；
B——Magnetic flux density,T；
D——Internal diameter of measuring pipe,m；
V——Average velocity of pipe section,m/s.
MLF Series Electromagnetic Flow Meter
Assume the volume of liquid as qv(m3/s),qv=πD2V/4),so in the
formula E=(4kB/πD)qv=kqv,
K is meter constant,K=4kB/πD.
3. Specification
| MLF Type | Divided Type | Integrated Type | Explosive Proof Integrated Type | Battery Powered Type | Heat Energy Type |
| Accuracy | ±0.2% or ±0.5% |
| Pipeline Diameter | DN10-DN2000 | DN10-DN600 | DN25-DN2000 |
| Flange | GB, ANSI, JIS, BS, Others |
| Pressure | DN10-DN600 1.0 1.6 2.5 4.0MPa |
| DN700-DN2000 0.6 1.0 1.6MPa |
| Liner Material | CR, PTFE, PU, Hard Rubber, PFA, FEP(F46) |
| Conductivity | ≥5µs/cm(Please contact us if it is less than 5µs/cm) |
| Electrode | 316L SS, Hb, Ta, Ti, Hc, Tungsten Carbide, Others |
| Protection Class | IP65, IP66, IP67, IP68 |
| Medium Temperature | -25~180℃
(Please refer to liner material) | -25~80℃(Please refer to liner material) | -25~180℃
(Please refer to liner material) |
| Ambient Temperature for Accuracy Influence | <±0.1%/10℃ or <±0.25%/10℃ at the ambient temperature of -25~60℃ |
| Repetability | ≤±0.1% or ±0.25% |
| Analog Output Error | ≤±0.02mA |
| Velocity | 0.3~10m/s |
| Electrical connection | M20x1.5 Seal Cartridge, GB1/2, NPT1/2 |
| Output | 4-20mA, Pulse, RS485, Hart, Profibus |
4. Configuration
| MLF Series Electromagnetic Flow Meter Configuration |
| Model | MLF |
| Sensor Installation | S | Flange Type Sensor |
| C | Insertion Type Sensor |
| O | Others |
| Pipeline Diameter | 10 | 10mm |
| 15 | 15mm |
| 20 | 20mm |
| ...... | |
| 2000 | 2000mm |
| Electrode Installation | F | Standard Fixed Type |
| Electrode Material | A | 316L SS |
| B | Hb |
| C | Ta |
| D | Ti |
| E | Hc |
| F | Tungsten Carbide |
| G | Others |
| Liner Material | R | Rubber |
| P | PTFE |
| O | Others |
| Pipe Material | B | 304 SS (Standard) |
| C | 316 SS |
| Flange Type | G | GB (Standard) |
| A | ANSI |
| J | JIS |
| B | BS |
| O | Others | |
| Flange Material | A | 304 SS |
| B | 316 SS |
| C | #20 Carbon Steel (Standard) |
| Cover Material | D | 304 SS |
| E | 316 SS |
| F | Carbon Steel+ Epoxy Metallic Paint (Standard) |
| Matching Flange | 0 | Without Matching Flange (Standard) |
| 1 | With Matching Flange |
| Ground Ring | 0 | Without Ground Ring (Standard) |
| 1 | With Ground Ring |
| Rated Pressure | 10 | 1.0MPa |
| 16 | 1.6MPa |
| 25 | 2.5MPa | |
| 40 | 4.0MPa |
| Working Temperature | E | ≤60℃ |
| H | ≤180℃(Divided Type) |
| Type | I | Integrated Type |
| D | Divided Type |
| Output | P | Pulse |
| A | 4-20mA |
| G | RS485 |
| H | Hart |
| Q | Others |
| Power Supply | 0 | 220VAC |
| 1 | 24VDC |
| 2 | Battery-powered |
| Protection Class | 0 | IP65 (Integrated/Divided Type) |
| 1 | IP67 (Divided Type) |
| 2 | IP68 (Divided Type) |
| Other Features | R | Heat Energy Function |
| P | With PT1000 |
| B | Without PT1000 |
| Explosion Proof | 0 | None |
| EX | Explosive Proof |
